Carrello

è vuoto

è vuoto
Disponibile

Waveshare UPS Hat (C) for Raspberry Pi Zero 5V Uninterruptible Power Supply Multi Battery Protection Circuits(Battery is not included)

Spedizione gratuita per ordini superiori a 25,99€
28,99€ -48%

14,99€

Informazioni su questo articolo

  • Alimenta il tuo Pi Zero senza problemi dalla connessione di alimentazione o dalle batterie di riserva
  • Supporta la ricarica e l'uscita regolata da 5 V allo stesso tempo, monitoraggio I2C
  • Perni pogo a molla integrati per il collegamento con schede Raspberry Pi serie Zero. Chip di ricarica della batteria Li-Po, con gestione dinamica del percorso, alimentazione più stabile
  • Chip di aumento della tensione, che fornisce un'uscita di potenza regolata da 5 V. Comunicazione bus I2C, monitoraggio della tensione della batteria, corrente, potenza e capacità residua in tempo reale
  • Multi circuiti di protezione della batteria: protezione da sovraccarico/scarica, protezione da sovracorrente e protezione da cortocircuito, più sicuro e stabile. Indicatore di ricarica per monitorare lo stato di funzionamento della batteria. Viene fornito con risorse di sviluppo e manuale


The UPS HAT (C) is an uninterruptible power supply module specialized for Raspberry Pi Zero series.
It incorporates Li-po battery switching charger with path management, voltage boost chip, and voltage/current monitor which allows monitoring the battery operating status via I2C bus.
It is able to recharge the battery and provide power output at the same time from external power supply.
Automatically switch over to battery output if external power supply is unavailable, keeps the system running without any trouble.
Designed For Raspberry Pi Zero Series.
Bottom Pogo Pin Connection, Allows Attaching Other HATs On The Top
Real Time Monitoring.
Monitoring The Battery Voltage, Current, Power, And Remaining Capacity Via I2C.
When the voltage dips too low, it is possible to save files properly and then shutdown the system by software, to avoid any data loss.
User Manual
www.waveshare.com/wiki/UPS_HAT_(C)?amazon


kekeke
Recensito in Germania il 30 agosto 2024
Purchased this hat with the battery recommended by Amazon and nearly burned it right away because the polarity of the Hat and the battery were reversed. BE CAREFULhttps://www.amazon.de/-/en/Lithium-Polymer-Battery-Rechargeable-Connector/dp/B08FD39Y5R/ref=pd_bxgy_d_sccl_1/262-1080977-0692423?pd_rd_w=A9PPY&content-id=amzn1.sym.049d9fe5-326c-4463-9183-bdeeaea54956&pf_rd_p=049d9fe5-326c-4463-9183-bdeeaea54956&pf_rd_r=NV3BHM3YKSBD8N2PM1TM&pd_rd_wg=33Pay&pd_rd_r=b3a4a3a5-4da5-44be-a291-acbe017dd63d&pd_rd_i=B08FD39Y5R&psc=1Not an issue to the product, but amazon recommends a battery which does not fit into hat: the battery length is 51 mm, and there is only about 34 mm space available to fit inside. Be careful with that too.Beside that, everything seems to be working fine.
JHoney
Recensito negli Stati Uniti il 14 ottobre 2024
This still sticks with the micro USB connector which is unfortunate, but that's what RPi has done so at least it is consistent.The charge light blinks whenever the module is supplied power, even if there is no battery attached.I like that waveshare defines all the components used in the product images. I don't think I've seen that level of detail before on a product without going to the their wiki.It is a little fiddly to attach to the Pi. Once it is together it makes a solid little unit.If you mistakenly connect the battery in reverse the device gets super hot (80°C+). Nothing seems to have been damaged when I did that. Important to remember that there is no standard polarity for JST connector.Operation has been good. I put it with a 900mAh cell, Pi Zero W 1.1, and 2.13 e-Paper Hat v4 to make a pwnagotchi. I can get 3-4 hours per charge.
Charles Whitt
Recensito negli Stati Uniti il 5 marzo 2024
Fits my Raspberry Pi Zero 2 W perfectly, the included hardware is perfect for the project case I have, standing off the UPS board about 1/4". The adhesive patch for the LiPo battery (not included) is a nice touch.As mentioned by John in his review, check the plug polarity of your battery against the UPS board (marked in + and -). The battery I bought had the wires reversed to the need of the board. I was able to pull up (gently) on the little white tabs in the photo and pull the wires out of the terminal, then reinserted them in the proper polarity.Double check the seating of the pogo pins before tightening your screws, and when you have it all together, you'll have a nice little battery backed up single board computer.
John
Recensito negli Stati Uniti il 30 settembre 2023
WARNING!!!! Make sure to triple check the polarity before plugging in any batteries.I instantly fried this board because the positive/negative is reverse from all the PH2.0 batteries I have from flying drones and the 10000mAh battery I specifically purchased for my project. Waveshare did reach out to try and make things right, but I accept the fault for assuming.
NicholasKrupa
Recensito negli Stati Uniti il 31 marzo 2023
It works have been using it for a project for over a year now even the made battery monitoring script have no complaints thus far.

Potrebbe piacerti anche